One-step synthesis of Ni/yttrium-doped barium zirconates catalyst for on-site hydrogen production from NH3 decomposition

On-site produced hydrogen from ammonia decomposition can directly fuel solid oxide fuel cells (SOFCs) for power generation. The key issue in ammonia decomposition is to improve the activity and stability of the reaction at low temperatures. In this study, proton-conducting oxides, Ba(Zr,Y) O_3-δ (BZY), were investigated as potential support materials to load Ni metal by a one-step impregnation method. The influence of Ni loading, Ba loading, and synthesis temperature, of Ni/BZY catalysts on the catalytic activity for ammonia decomposition were investigated. The Ni/BZY catalyst with Ba loading of 20 wt%, Ni loading of 30 wt%, and synthesized at 900 °C attained the highest ammonia conversion of 100% at 600 °C. The kinetics analysis revealed that for Ni/BZY catalyst, the hydrogen poisoning effect for ammonia decomposition was significantly suppressed. The reaction order of hydrogen for the optimized Ni/BZY catalyst was estimated as low as ?0.07, which is the lowest to the best of our knowledge, resulting in the improvement in the activity. H₂ temperature programmed reduction and desorption analysis results suggested that a strong interaction between Ni and BZY support as well as the hydrogen storage capability of the proton-conducting support might be responsible for the promotion of ammonia decomposition on Ni/BZY. Based on the experimental data, a mechanism of hydrogen spillover from Ni to BZY support is proposed.     

Rapid preparation of Palygorskite/Al2O3 composite aerogels with superhydrophobicity,high-temperature thermal insulation and improved mechanical properties

Al₂O₃ aerogels are widely employed in heat insulation and flame retardancy because of their unique combination of low thermal conductivity and exceptional high-temperature stability. However, the mechanical properties of Al₂O₃ aerogel are poor, and the preparation time is considerably long. In this study, we present a simple and scalable approach to construct monolithic Pal/Al₂O₃ composite aerogels using solvothermal treatment instead of traditional solvent replacement, which remarkably shortened the preparation time. Subsequently, to obtain stable superhydrophobicity (θ > 152°), the Pal/Al₂O₃ aerogel was modified by gas-phase modification method. The obtained Pal/Al₂O₃ composite aerogels demonstrate the integrated properties of low density (0.078–0.106 g/cm³), low thermal conductivity (1000 °C, 0.143 W/(m·K)), good mechanical properties (Young's modulus, 1.6 MPa), and good heat resistance. The monolithic Pal/Al₂O₃ composite aerogels with improved mechanical performance and improved thermal stability can show great potential in the field of thermal insulation.     

Effects of hydrogen plasma treatment on the physical and chemical properties of tin oxide thin films for ambipolar thin-film transistor applications

In this study, we investigated the physical and chemical properties of H₂ plasma-treated tin oxide (SnO_X) thin films, followed by their applications in ambipolar thin-film transistors (TFTs). Finely controlled H₂ implantation was carried out using a reactive-ion-etching system at a radio frequency power of 30 W and under various exposure times. H₂ plasma treatments induced changes in the chemical structures and surface morphologies of the SnO_X thin films, including a partial phase transformation of Sn and SnO to SnO₂. The defects originating from oxygen vacancies (O_Vacs) in the SnO_X thin films were passivated by H via the formation of Sn–H bonds, which decreased the density of subgap states in the SnO_X thin films. The H₂ plasma-treated SnO_X TFTs showed considerably improved ambipolarity and electrical performance. Complementary metal–oxide–semiconductor (CMOS) logic inverters comprising H₂-plasma-treated ambipolar SnO_X TFTs exhibited a maximum gain of 34.5 V/V at a supply voltage of 10 V. The results of this study present the meaningful investigation of H₂ plasma-treated ambipolar SnO_X TFTs that can be used to fabricate CMOS circuits for various applications.     

Effect of heat treatment on the roughness and mechanical properties of dental lithium disilicate glass-ceramics

In dental clinics, it is common to perform small fitting adjustments in dentures using a micro-grinding tool after testing them in the patient's mouth. This procedure increases local roughness and can lead to formation of microcracks on the prosthesis surface. This study aimed to investigate the benefits of a post-finishing heat treatment to surface roughness and crack healing and its effect on the flexural strength of lithium disilicate (LD) dental glass-ceramics. Commercially available lithium metasilicate, Li₂SiO₃, samples were heat treated at 840 °C for 7 min to induce the phase transformation into LD, Li₂Si₂O₅. The LD samples were characterized by X-ray Diffraction, Scanning Electron Microscopy, Vickers hardness, Young’s modulus, and fracture toughness. One of the surfaces of the LD samples was sanded aiming to simulate the denture fitting adjustments performed in the dentist’s laboratory, generating a rough surface, Group 1. Half of the LD samples had their biaxial flexural strength evaluated by the piston-on-three-ball test (P–3B) and the other half were submitted to a second short-term heat treatment (840 °C - 5 min), Group 2, and later assessed by the P–3B. Roughness parameters in both groups were measured by 3D optical profilometry. After the crystallization heat treatment, formation of elongated LD crystals, Li₂Si₂O₅, 35% amorphous phase, and residual Li₃PO₄ was observed. In addition, the following mechanical property values were obtained: Vickers hardness = 5.8 ± 0.1 GPa, fracture toughness = 2.2 ± 0.1 MPa m^1/2, and Young’s modulus = 100.3 ± 0.3 GPa. The samples in Group 1 showed bending strength of 206 ± 30 MPa and the following roughness parameters: Ra = 0.45 ± 0.16 μm, Rz = 22.7 ± 6.7 μm, and PV = 27.7 ± 7.1 μm. In the samples in Group 2, the Ra, Rz and PV roughness parameters were 0.31 ± 0.12 μm, 5.2 ± 2.5 μm, and 9.2 ± 4.7 μm, respectively. With this decrease in roughness, the bending strength increased by 62%, with a mean value of 331 ± 59 MPa. In the need for machine finishing of LD-based glass-ceramic dental prostheses, the use of a second short-term heat treatment at 840 °C for 5 min generates considerable gains in bending strength, increasing the lifecycle of the prosthesis as a result of reduced surface roughness caused by softening of the remaining amorphous phase in the glass-ceramic. These conditions can be adapted to each chemical and crystallographic composition of the glass-ceramic under study.     

《安徽省农村供水工程运行管理指南（试行）》解析

“十四五”期间，通过强化供水工程运行管理，巩固维护好已建农村供水工程成果，是水利部门实施乡村振兴的基本任务。2021年4月，《安徽省农村供水工程运行管理指南（试行）》正式印发实施。《指南》是在安徽省农村供水工作重点由工程建设转入运行管理的背景下，指导推进农村供水工程规范化管理的重要文件。通过介绍《指南》编制的有关背景、编制目标和特点，解析《指南》的主要内容和条款，可帮助供水管理人员快速掌握《指南》要点，助力《指南》在安徽省内贯彻和实施。     

Ammonia mitigation and induction effects on hydrogen environment embrittlement of SCM440 low-alloy steel

The effect of ammonia (NH₃) contained in hydrogen (H₂) gas on hydrogen environment embrittlement (HEE) of SCM440 low-alloy steel was studied in association with the NH₃ concentration, loading rate, and gas pressure. NH₃ worked as both mitigator of the HEE and inducer of hydrogen embrittlement (HE) depending on the testing conditions. The mitigation of the HEE was achieved by the deactivation of the iron (Fe) surface for H₂ dissociation caused by the preferential adsorption of NH₃ on the Fe surface, which is enhanced by the increase in the NH₃ concentration and decrease in the H₂ gas pressure. NH₃ induced HE was caused due to creating hydrogen by the NH₃ decomposition. Since the NH₃ decomposition rate is low, the induction effect was observed when the loading rate was low. The effect of NH₃ was determined by the competition of the mitigation and induction effects.     

Ni2P(O)–Fe2P(O)/CeOx as high effective bifunctional catalyst for overall water splitting

The development of cost-effective bifunctional catalysts with excellent performance and good stability is of great significance for overall water splitting. In this work, NiFe layered double hydroxides (LDHs) nanosheets are prepared on nickel foam by hydrothermal method, and then Ni₂P(O)–Fe₂P(O)/CeO_x nanosheets are in situ synthesized by electrodeposition and phosphating on NiFe LDHs. The obtained self-supporting Ni₂P(O)–Fe₂P(O)/CeO_x exhibit excellent catalytic performances in alkaline solution due to more active sites and fast electron transport. When the current density is 10 mA cm^?2, the overpotential of hydrogen evolution reaction and oxygen evolution reaction are 75 mV and 268 mV, respectively. In addition, driven by two Ni₂P(O)–Fe₂P(O)/CeO_x electrodes, the alkaline battery can reach 1.45 V at 10 mA cm^?2.     

Effect of support and reduction temperature in the hydrogenation of CO2 over the Cu–Pd bimetallic catalyst with high Cu/Pd ratio

Metal-support interaction and catalyst pretreatment are important for industrial catalysis. This work investigated the effect of supports (SiO₂, CeO₂, TiO₂ and ZrO₂) for Cu–Pd catalyst with high Cu/Pd ratio (Cu/Pd = 33.5) regarding catalyst cost, and the reduction temperatures of 350 °C and 550 °C were compared. The activity based on catalyst weight follows the order of Si > Ce > Zr > Ti when reduced at 350 °C. The reduction temperature leads to the surface reconstruction over the SiO₂, CeO₂ and TiO₂ catalysts, while results in phase transition over Cu–Pd/ZrO₂. The effect of reduction temperature on catalytic performance is prominent for the SiO₂ and ZrO₂ supported catalysts but not for the CeO₂ and TiO₂ ones. Among the investigated catalysts, Zr-350 exhibits the highest methanol yield. This work reveals the importance of the supports and pretreatment conditions on the physical-chemical properties and the catalytic performance of the Cu–Pd bimetallic catalysts.     

Simply constructed highly dispersed cobalt nanoparticles in diverse N-doped graphitic carbon with remarkable performances for water electrolysis

Metal/carbon composite materials are highly promising electrocatalysts for water electrolysis. In this work, three composites of metal cobalt nanoparticles highly dispersed in N-doped carbon materials were facilely constructed by pyrolysis of different phenylenediamine based Schiff base-Co complexes (PDBs). Interestingly, the composites derived from PDBs based on different phenylenediamine exhibited different morphologies. The superior case is that rodlike composite catalyst was derived from o-phenylenediamine based PDBs. The obtained catalyst exhibited remarkable performances for both cathodic hydrogen evolution reaction (HER) and anodic oxygen evolution reaction (OER), as well as overall water electrolysis. Only 172 and 289 mV of overpotentials and 1.57 V of cell voltage were exhibited at 10 mA cm^?2 for HER, OER and water splitting in 1.0 M KOH, respectively. The catalyst also displayed robust stability and high Faraday efficiency, and thus are potential high-performance catalyst for commercial water electrolysis.     

Effects of non-thermal plasma treating wheat kernel on the physicochemical properties of wheat flour and the quality of fresh wet noodles

The effects of non-thermal plasma (NTP) on the physicochemical properties of wheat flour and the quality of fresh wet noodles ( FWN) were investigated. The results showed that NTP effectively decreased the total plate count (TPC), yeast and mould count (YMC) and Bacillus spp. in wheat flour. Wet gluten contents and the stability time reached the maximum when treated for 20 s. The viscosity of starch increased significantly after treatment due to the increased of damaged starch. The contents of secondary structure were altered to some extent, which was because that the ordered network structure of gluten protein broken. Furthermore, compared with the control, texture properties of FWN were enhanced significantly at 20 s, and the darkening rate of FWN was greatly inhibited due to the low polyphenol oxidase (PPO) activity. Consequently, the most suitable treatment was 500 W for 20 s, providing a basis for the application of NTP in flour products.